LD400P电子负载,Aim-tti LD400P厂家代理 LD400P电子负载,Aim-tti LD400P厂家代理

LD400P电子负载,Aim-tti LD400P厂家代理:600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of...

广州赢韬仪器有限公司主要经销批发数字存储示波器、频谱分析仪、数字电桥LCR、台式万用表、安规测试仪、音频测试仪、数据记录测试仪、温度记录仪、数据采集器、直流电子负载、电能质量分析仪、可编程交流电源、电池内阻测试仪、LED光谱仪器、以及其他仪器仪表目前畅销消费者市场，在消费者中享有较高的地位，公司与多家零售商和代理商建立了长期稳定的合作关系。广州市赢韬仪器有限公司经销的数字存储示波器、频谱分析仪、数字电桥LCR、台式万用表、安规测试仪、音频测试仪、视频制式测试仪、电子负载、电能质量分析仪、电参数测试仪、电池测试仪、LED光谱仪器、电源测试仪、其他仪器仪表品种齐全、价格合理。深圳市美孚科技有限公司实力雄厚，重信用、守合同、保证产品质量，以多品种经营特色和薄利多销的原则，赢得了广大客户的信任。
广州赢韬仪器有限公司本着互利发展、资源共享、服务一的原则，依托广东珠江三角洲巨大的市场，辐射全国。广州市赢韬仪器有限公司专注与完善的（仪器配套方案）（解决方案）（技术支持）高性能、高品质、高效率的全程式服务跟踪。代理国内外品牌厂商多达20多家，多年来不懈努力的为客户服务！主营产品、示波器、频谱仪、信号发生器、音频测试仪、安规测试仪、数字电桥、功率计、AC/DC变频电源、万用表、钳形表、电流探头等各类仪器仪表！主营品牌：美国安捷伦-AGILENT、美国泰克-Tektronix、美国福禄克-FLUKE、日本横河-YOKOGAWA、菊水-KIKUSUI、日本德仕-TEXIO、日置-HIOKI、共立-KYORITSU、台湾固纬-GWINSTEK、台湾华仪-EXTECH、台湾艾德克斯-ITECH、杭州远方-EVERINE、同惠、优利德、北京普源、安泰信等仪器。
本公司的（仪器配套方案）（解决方案）（技术支持）承载这客户的考验！如果您需要本公司的支持、请一时间联系我们的客服。我们将竭诚为阁下服务！

    在互联网迅猛发展的今天，本公司将放眼世界，利用互联网这个强有力的信息工具，将我们的品牌再次提升，让赢韬仪器有限公司更好地为广大用户服务。
公司理念：秉承坦诚、公道求新、务实、和气生财之经营理念，以“诚信服务”为公司之宗旨。公司将不懈致力于客户之需求.

 LD400P电子负载,Aim-tti LD400P厂家代理: 

LD400P

Electronic DC Load, 80V, 80A, 400W with analogue and digital control, USB, RS232, LAN (LXI) and GPIB

• Versatile solution for testing dc power sources
• Constant current, resistance, conductance, voltage and power modes
• Wide voltage and current range, 0 to 80V and 0 to 80A
• 400 watts continuous dissipation at 28oC (360W at 40oC)
• 600 watts short-term dissipation (up to 60 seconds)
• Low minimum operating voltage of <1V at 40A
• High resolution and accuracy for level setting
• Built-in transient generator with variable slew
• Current monitor output for waveform viewing
• Variable drop-out voltage for battery testing
• High resolution backlit graphic LCD with soft key control
• Analog remote control of levels and TTL control of on/off
  and transient switching
• Front and rear input terminals (front terminals 30A max.)
• Full bus control via USB, RS232, GPIB and LXI compliant LAN interfaces (LD400P)

LD400P电子负载,Aim-tti LD400P厂家代理: 

Versatile and inexpensive load testing

The LD400 is an inexpensive 400 watt electronic load which is suitable for testing and characterising a wide variety of dc power sources. It can be used to investigate the behaviour of many different types of power source such as batteries and solar cells, as well as electronic power supply units. Its wide voltage/current range, multiple operating modes and built-in transient generator give it the versatility to offer test solutions from the design laboratory through to the component test area. The LD400P adds full bus remote control via USB,  RS-232, GPIB and LAN (Ethernet) interfaces.

80 volts, 80 amps and up to 600 watts

Subject to its maximum power ratings, the LD400 can operate at up to 80 volts or up to 80 amps. It can operate at power levels up to 600 watts for periods of up to 1 minute.  Short term loading can be sufficient for many testing applications and significantly extends the usefulness. Low minimum operating voltage The LD400 can operate at voltages below 500mV for currents up to 10 amps. At higher currents the fixed minimum resistance (typically better than 25milliOhms) gradually raises the minimum operating voltage, but it remains below 1 volt up to 40 amps and below 2 volts up to 80 amps. This low operating voltage allows it to be used for many low voltage applications for which other electronic loads are unsuitable. Multiple modes of operation The LD400 can operate in constant current, constant resistance, constant conductance, constant voltage or constant power modes. Transient generator and variable slew The LD400 incorporates a full variable frequency, variable duty cycle transient generator. Switching between the two preset levels can be done at any frequency between 0.01Hz and 10kHz. The transient generator can be used in all operating modes.  The rate of change between levels (slew rate) is controllable over a wide range.

LD400P电子负载,Aim-tti LD400P厂家代理: 

Maximum Input Ratings

Current: 80 Amps max. through the rear panel terminals. 30 Amps max. through the front panel terminals
Voltage: 80 Volts max. while conducting current. Surge suppressors start to conduct at 120V (nominal), 
Max. non-repetitive surge energy: 80 Joules.
Power Continuous: 400 Watts max. up to 28ºC, derating to 360 watts at 40ºC.
(1) Power Short Term: 600 Watts max. up to 28ºC, for up to 60 seconds on-time, with off time 
at least double the on time.
Min. Operating Volts: <2V at 80A; typically equivalent to 25 mOhm above 100mV (at 4A). 
Off State Leakage: <10 mA (including voltage sense circuit input resistance). 
Reverse Polarity: Diode will conduct; 80 Amps max.
Isolation Voltage: ± 300Vdc max, either load input to chassis ground.

Input Terminals
Rear Panel Input: Safety terminals accepting 5mm diameter wire, or 8mm spades up to
80 Amps max., or 4mm plugs at 30 Amps max.
Front Panel Input: Safety terminals accepting 4mm diameter wire, 4mm plugs or 6.5mm 
spades up to 30 Amps max.

External Voltage Sense
Connection: Terminal block on rear panel. Sense selection by slide switch. 
Input Impedance: 680kOhm each input to load negative.
Max. Sense Offset: 6V (allowance for backing-off supply for zero volt operation)

OPERATING MODES

Constant Current Mode (CC)
Current Ranges: 0 to 8 A (1 mA resolution) and 0 to 80 A (10 mA resolution).
Setting Accuracy: ± 0.2% ± 30 mA.
Regulation: < 30 mA for 90% load power change (V > 2 Volts).
Temp. Coefficient: < (±0.02% ± 5 mA) per ºC. 
(2) Slew Rate Ranges: 8 A range: <2.5 Amp per s to >250 Amp per ms.
80 A range: <25 Amp per s to >2500 Amp per ms.
(3) Min. transition time: 50 µs.

Constant Power Mode (CP)
Power Range: 0 to 400 (or 600) Watts.
Setting Accuracy: ± 0.5% ± 2 W ± 30mA).
Regulation: < 2% over 5 V to 75 V source voltage change (using remote sense).
Temp. Coefficient: <(± 0.1% ± 5mA) per ºC.
(2) Slew Rate Ranges: <40 W per s to >6000 W per ms.
(3) Min. transition time: 150 µs.

LD400P电子负载,Aim-tti LD400P厂家代理: 

Constant Resistance Mode (CR)
Resistance Ranges: 0.04 to 10Ohm (0.01Ohm resolution); 2 to 400Ohm (0.1Ohm resolution).
Setting Accuracy: ±0.5% ± 2 digits ± 30 mA. 
Regulation: < 2% for 90% load power change (V > 2 Volts, using remote sense).
Tem. Coefficient: < (±0.04% ± 5 mA ) per ºC. 
(2) Slew Rate Ranges: 10Ohm range: <1Ohm per s to 100Ohm per ms. 
400Ohm range: <40Ohm per s to 4000Ohm per ms.
(3) Min. transition time: 150 µs.

Constant Conductance Mode (CG)
Conductance Ranges: <0.01 to 1 A/V (1 mA/V resolution); <0.2 to 40 A/V (0.01 A/V resolution).
Setting Accuracy: ± 0.5% ± 2 digits ± 30 mA. 
Regulation: < 2% for 90% load power change (V > 2 Volts, using remote sense).
Temp. Coefficient: < (±0.04% ± 5 mA) per ºC. 
(2) Slew Rate Ranges: 1 A/V range: <0.1 A/V per s to >10 A/V per ms. 
40 A/V range: <4 A/V per s to >400 A/V per ms.
(3) Min. transition time: 150 µs.

Constant Voltage Mode (CV)
Voltage Ranges: Vmin to 8 V (1 mV resolution) and Vmin to 80 V (10 mV resolution).
Vmin depends on current: typically <2V at 80A
Setting Accuracy: ± 0.2% ± 2 digits.
Regulation: < 30 mV for 90% load power change (using remote sense).
Temp. Coefficient: < (0.02% + 1 mV) per ºC.
(2) Slew Rate Ranges: 8 V range: <0.8 V per s to >80 V per ms.
80 V range: <8 V per s to >800 V per ms.
(3) Min. transition time: 150 µs.

TRANSIENT CONTROL

Transient Generator
Pulse Repetition Rate: Adjustable from 0.01Hz (100 seconds) to 10kHz.
Pulse Duty Cycle: 1% to 99% (percentage of period at Level A).
Setting Accuracy: ±1 %
Slew Rate Control
The slew rate control applies to all changes of level whether caused by manual selection, remote control or the transient generator. The level change is a linear slew between the two level settings. The range available in each mode is shown above.
Setting Accuracy: ± 10% (on linear part of slope, excluding high frequency aberrations).
Variation in Level 
Settings: ± 5 digits of specified setting resolution for present mode and range.
Oscillator Sync Output
Connection: Terminal block on rear panel. Opto-isolated open collector output 
conducts during Level B phase of internal transient generator.
Ratings: Max Off State Voltage: 30V. Collector Current: 2mA (typical).

DROPOUT VOLTAGE

The load will cease to conduct if the applied voltage falls below the Dropout Voltage setting; active in all modes except Constant Voltage. The Dropout Voltage setting is also the threshold for the Slow Start facility and acts as an offset voltage in Constant Resistance mode.
Setting Accuracy: ± 2% ± 20mV.
Slow Start
If Slow Start is enabled, the load will not conduct any current until the source voltage reaches the Dropout Voltage setting; it will then ramp the controlled variable up (in CC, CP and CG modes) or down (in CR and CV modes) to the Level setting at a rate determined by the Slew Rate setting.

METER SPECIFICATIONS

Display Type: 256 x 112 pixel backlit graphic LCD.
Measured Values
Volts & Amps: Measured values of current through and voltage across the load.
Watt & Ohms: Power and equivalent load resistance, calculated from Volts and Amps. 
Voltage Accuracy: ± 0.1% ± 2 digits.
Current Accuracy: ± 0.2% ± 3 digits.

CURRENT MONITOR OUTPUT

Output Terminals: 4mm safety sockets on front panel or terminal block on rear panel.
Output Impedance: 600W nominal, for >1MW load (e.g. oscilloscope)
Scaling: 50mV per Amp (4 Volts full scale).
Accuracy: ± 0.5% ± 5mV.
Common Mode Range: ± 3V dc max. See note (4).

ANALOG REMOTE CONTROL (LD400 and LD400P)

External Control Input Characteristics
Connection: Terminal block on rear panel.
Input Impedance: 400kOhm each input to load negative.
Common Mode
Range: ± 100V to load negative.
External Analogue Voltage Control
Operating Mode: The applied voltage sets the operating level within the selected range.
Scaling: 4 Volts full scale.
Accuracy: ± 2% ± accuracy of selected range.
Common Mode
Rejection: Better than –66dB.
External Logic Level (TTL) Control
Operating Mode: The applied signal selects between Level A and Level B settings.
Threshold: + 1.5V nominal. A logic high selects Level B.
Remote Disable Input
Connection: Terminal block on rear panel. 
Input to the LED of an opto-isolator through 1kW resistor.
Threshold: Apply >+3V to disable load input (+12V maximum).

DIGITAL REMOTE CONTROL (LD400P only)

Digital Remote Interfaces
The LD400P model provides LAN, USB, GPIB and RS232 interfaces for full remote control.
LAN: Ethernet 100/10base-T connection with auto cross-over detection. LXI v1.4 Core 2011 compliant.
USB: Standard USB 2.0 connection. Operates as virtual COM port.
GPIB: Conforming to IEEE488.1 and IEEE488.2.
Capabilities: SH1, AH1, T6, L4, SR1, RL2, PP1, DC1, DT0, C0, E2.
RS232: Standard 9-pin D connection. Baud rate: 9600.

LD400P电子负载,Aim-tti LD400P厂家代理: 

PROTECTION

Excess Power: The unit will attempt to limit the power to approx 430 Watts; if this fails the unit will trip into the fault state at about 460 Watts. If intermittent mode operation is enabled, these levels are 610W and 630W.
Protection Current: The input is disabled if the measured current exceeds a user set limit.
Excess Current: The unit will trip into the fault state at nominally 92 Amps.
Protection Voltage: The input is disabled if the measured voltage exceeds a user set limit.
Excess Voltage: The unit will conduct a current pulse (to absorb inductively generated spikes) for 1ms at about 90V.
The unit will trip into the fault state at nominally 106V
Surge suppressors will start to conduct above 120V.
Temperature: The unit will trip into the fault state if the heatsink temperature exceeds safe levels.
Sense Error: The unit will trip into the fault state if the external voltage sense is more than 6V below the internal sense.

GENERAL

AC Input: 110V–120V or 220V–240V AC ±10%, 50/60Hz. Installation Category II.
Power Consumption: 30VA max. Mains lead rating 6A.
Operating Range: + 5ºC to + 40ºC, 20% to 80% RH.
Storage Range: – 40ºC to + 70ºC.
Environmental: Indoor use at altitudes up to 2000m, Pollution Degree 2.
Cooling: Variable speed fan. Air exit at rear.
Safety: Complies with EN61010-1 and EN61010-2-030.
EMC: Complies with EN61326.
Size: 130mm H (3U) x 212mm W (½ rack) x 435mm D.
Weight: 5.7 kg.

OPTIONS

Option: 19-inch rack mount kit.

Specification Notes
(1) In 600 Watt short-term operation mode the dynamic response is not specified, and both the slew rate and the transient oscillator frequency range are restricted. The slew rate limitation applies also to external voltage control. This mode is primarily intended for limited duration operation at a fixed level setting.
(2) Slew Rate Ranges refer to the theoretical slope of the transition between two levels, regardless of whether that transition can be achieved when taking into account the level difference, the set transition duration, the minimum transition time, and the characteristics of the source.
(3) Minimum Transition Time specification is an indication of the fastest available transition using a benign battery source and low inductance connections, with a minimum terminal voltage of 5V and a minimum current of 1A. The actual performance attainable with electronically regulated power supplies depends on the combination of source and load loop bandwidths and interconnection inductance. 
(4) The common mode capability of the current monitor is to provide tolerance of voltage drops in the cables. The monitor negative must be connected at some point to the load negative circuit.

Accuracy specifications apply for 18°C – 28ºC, at 50W load power (in normal 400W mode), after 30 minutes operation at the set conditions; regulation specifies variation at other powers. Setting accuracies apply with slew rate at the ‘Default’ setting.

本页产品地址：http://www.yi7.com/sell/show-6456613.html